Crib & Toddler Bed Sheet Tutorial!
February 6, 2008
Well I got quite a few people asking if the crib sheets were easy to make, & yes they are! The longest part is the elastic, the rest only takes a few minutes. Anyways I have made this for a while & used a few different patterns, but none of them have good pictures!!! So I decided once again that I would make my own tutorial to share with everyone! Here ya go…
CRIB/ TODDLER BED SHEET TUTORIAL…
They are SUPER easy to make & a HUGE money saver, you can even make them out of old sheets from the thrift store! Some patterns call for a little less fabric, but I like this sizing because it fits over the mattress VERY well with the extra on the back, & I have never had any of them come off my sons bed. The standard US crib mattress is approx. (they all vary a little bit) 51 5/8″ X 27 1/4″ and range from 4″-6.5″ thick. Because of the way this pattern is designed it will fit mattresses that are a little bigger/thicker or a little smaller/thinner. If the sheet is a little loose on your mattress you can fix this on the next one you make by using the same length of elastic but making it stretch a few inches farther when you sew it on… this should tighten it nicely.
You need 2 yards of woven (no stretch) PRE-WASHED fabric. knits stretch all over, but not in the seams so they require different measurements
4 12″ pieces of 1/4″ or 3/8″ elastic
Scissors or Rotary cutter
Sewing Machine
Matching thread…
First you want to cut your fabric to be 45″ X 69″ (45″ X 70″ if you want to hem the ends) piece of Fabric. This MUST be pre-washed, otherwise the first time it is washed it will never fit the mattress as well again!
Next if you want to just serge or zig zag the raw edges then you just do that.
This is what you end up with…
If you want to hem the raw edges then cut it 70″ instead & on each end fold it under 1/4″ & then again another 1/4″ to hide the raw edge & sew it down!
Then you take your big rectangle that you now have & you cut 8″x8″ squares out of each of the 4 corners. I have found the easiest way to do this is to fold the fabric in half so your newly finished edges meet. Then take the edge that we haven’t done anything to & fold it over to the matching edge… this quarters it & puts all 4 corners in the same place. Here are the pics…
Lay your 8″ by 8″ template down & cut it out of a.. 4 layers. You can also do it one corner at a time.
This is what you’ve got…
Then with the WRONG side of your fabric facing up you want to match to two side that are now left from where you cut the square out together & sew (I use 3/8″ seams, its up to you!) Do this to all 4 corners.
When you look at the right side of the fabric it should look like this…
Next is the elastic! Fold the elastic in half & mark the center… now line this up with the edge of the seam you just made (again on the out side of the fabric) & pin in place. Then you want to mark out 12″ from both sides of that point & pin the lose ends of the elastic to the sheet.
When you have the middle & both ends pinned in place it should look something like this…
Now with your machine set to zigzag… I found the width 5-7 works best depending on the with of your elastic. I also set my stitch length to 4, or the longest or ‘basting’ stitch that your machine has. Now place your starting end under the needle & lower the pressure foot, you want to make a few stitches & back stitch or two to make sure it is secured & stop with the needle in the down position. Now you want to grab the next pin & stretch it so the fabric is tight… holding both the back & front of the fabric, pull it through as sew… once you needle gets to the next pin, grab the last pin & repeat, just make sure to back stitch it to secure the end. Again this is done to all 4 corners & then you are done!
This is what the corners should look like when your done…
And when on the mattress!!!
UPDATE: I have had a lot of interest from mamas in other countries & wanted to list the metric measurements to help answer some of your questions! The standard US crib mattress (what this is made for) is approx. 130cm X 69cm & can range from 10-16cm deep. Even if yours is a little bigger or smaller in either direction these should still fit! If the sheet is a little loose to your liking then stretch your elastic a little farther next time to tighten it.
Here are the metric conversions…
You will want to purchase 1 3/4 meters of fabric You will want your fabric to be 114cm X 175cm
You will want 4 pieces of 31cm long 6-10mm wide elastic.
The squares you cut out of the 4 corners will be 20cm x 20cm.
Entry Filed under: Babies & Kids, Sewing, Tutorials. Tags: cot, cot sheet, Crib mattress, crib sheet, elastic, fabric, instructions, pattern, photos, pictures, Sewing, sheet, toddler, toddler bed, toddler sheet, tutorial.
78 Comments Add your own
Leave a Comment
Some HTML allowed:
<a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <pre> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>
Trackback this post | Subscribe to the comments via RSS Feed
1.
Nicole | February 6, 2008 at 2:17 PM
Awesome! Thanks for the tute with the pictures! Can’t wait to try these~
2.
Kerri | March 19, 2008 at 7:26 PM
WOW! I haven’t sewn since grade 8, which was a while ago (haha) I followed your directions and success! My son now has a brand spank’n new CARS fitted sheet!!! I will be making many more, thank you for your wonderful directions w/ pictures they made a world of difference.
3.
Elisha | June 4, 2008 at 4:41 AM
Finally understandable directions! Thanks a bunch
4.
Amber | June 17, 2008 at 11:44 PM
Thanks for the picture tutorial. Mine turned out not as tight as Id like but I still love it. Thanks so much now I know how to make these. My daughter loves her new Dora fitted bed sheet.
5.
Kymy | June 18, 2008 at 1:32 PM
I’m am glad everyone is so happy with them
. Amber, crib mattresses are all a little different in size, some brands are up to 2″ thicker then others! Also if they have gone through a few kiddos, bigger kiddos or just a few years of use they will thin out a bit. If you email me the measurements of your crib mattress width, length & height I can get you measurements that will work better for your mattress!
6.
kate easton | July 5, 2008 at 7:06 PM
Hi there, am hanging out to make Baby Hugo some fitted sheets for his cot. Have found your wonderful website, Our mattress is 1300mm x 690mm and 100mm deep, are you able to please recommend the measurements that would work best with this mattress. Many thanks Kate (Brisbane-Australia)
7.
Kymy | July 5, 2008 at 11:58 PM
Kate I am glad you found my site & here are the answers you were looking for! Your mattress is the same size as a standard US crib mattress! That means the measurements that I posted should work. Here are the metric conversions…
You will want to purchase 1 3/4 meters of fabric You will want your fabric to be 114cm X 175cm
You will want 4 pieces of 31cm long 6-10mm wide elastic.
The squares you cut out of the 4 corners will be 20cm x 20cm.
I hope this helps & would love to see pictures when your done
8.
melanie | August 14, 2008 at 10:30 AM
Thank you for these simple, easy to follow directions with great photos!!! These sheets came out perfect and I had so much fun making a Cars sheet for my son I whipped up a princess one for my daughter in no time!!!
9.
Sarah | August 25, 2008 at 10:34 PM
Hi! Thank you SO MUCH for the Picture Tutorial. It was really clear and straight forward.
I would also love to know how to make crib bumpers and box pleat crib skirts (all of the store patterns Ive seen have ruffles – YUCK). This would really finish off the crib set. Hope you’ll have time one of these days to tackle bumpers and skirts!
10.
Sonja Djipalo | November 16, 2008 at 1:08 AM
dear kymy I have just finished my red gingham cot sheet for my daughter Kitty(18 months) and I LOVE IT and it only cost me $7,amazing.thanks for yoer website its great it was the first time I have made something like this off the internet. And all the way to sydney Australia how cool is that .Thanks again for taking the time to offer this to everybody.I appreciate it love from down under sonja (mother of 3) xxx
11.
Elisa | December 13, 2008 at 4:05 AM
This looks great! I have not sewn in a while but I think I can do this. Any thoughts on a top sheet and/or “bigger” size quilt for older “toddler” age kids? I just converted my daughter’s crib into a daybed and I would love to give her a top sheet and bigger quilt to accommodate her larger than a baby size. This is a great place to start and I love the site! Thanks!!
12.
Elaine | January 4, 2009 at 5:17 AM
I’ve purchased stretchy fabric for the sheet. It’s a pretty tight stretch in a polyester fabric. Do I have to make any special accommodations to your design?
13.
Shane Bracewell | February 1, 2009 at 8:06 AM
Thank you so much. I take care of my grandson, and I have him nap in a play yard. I had a hard time finding sheets to fit. So now, I can make them, with your wonderful help. Thank you, Shane Catherine
14.
Melanie | February 13, 2009 at 3:20 PM
These are very interesting, but is there a pattern on how to make sheets for a daybed or twin bed?
15.
Kate | February 14, 2009 at 2:26 PM
Hey,
Thanks for posting these instructions. I have just one clarifying question… once I sew the elastic down, do I need to turn over the fabric to hide the elastic or does the elastic just go against the mattress? If that’s the case, how is the elastic affected in the washing machine? Thanks again! ~ Kate
16.
Vatsi | February 18, 2009 at 7:42 PM
Hey,
Thanks for the pictures of the project. Please tell me if I want to do this for my queen size bed, Should I still cut 8×8 or the size varies?
Thanks
17.
Donna Dodd | February 20, 2009 at 12:10 AM
THANK YOU! THANK YOU! THANK YOU! I’ve been looking for a guide to making crib sheets for a few months now. I made a fleece crib sheet a couple months ago. It turned out ok, but I didn’t trust myself while making it. i just made another sheet and your tutorial was so easy to follow! This time I used flannel. I wish I could add a picture on here of my little guy’s brand new sheet. Once again, THANK YOU!!!!
18.
Kymy | February 20, 2009 at 12:48 PM
You can email it too me via my ‘About Kymy’ page & I will put it on the gallery I am working on
19.
Elizabeth | February 26, 2009 at 3:12 PM
Thanks so much for your tutorial! I’ve never made crib sheets before, and they turned out great!
20.
Brianna | March 4, 2009 at 6:43 AM
Thank you so much for this tutorial it is so helpful, I even made a flat sheet for my son’s bed too, using the same method just with two corners instead of 4 and it turned out great! your pics are wonderful for us mothers who can’t read patterns worth a crap, and can’t afford 100 or 200 dollar bed sets for our children. thanks again!!
21.
katrina | March 31, 2009 at 9:36 AM
do you have a easy to follow twin size fitted sheet pattern?
22.
Martha | July 5, 2009 at 1:31 PM
I’ve made crib sheets in the past for my own children. BUT, thanks for doing the measuring and calculating (all the yucky math stuff) and posting this marvelous info.
23.
Jessica | July 10, 2009 at 9:22 PM
Thanks so much! The tutorial was easy to follow and my crib sheets turned out great!
24.
Rosemary | July 14, 2009 at 6:58 PM
wow! i can’t wait to do this for my babies to come! saves money and i can get exactly what i want and nobody else will have it! THANK YOU!
25.
Annie | July 15, 2009 at 2:48 PM
Thanks for this tutorial.. seems so simple- but sometimes we just need reassurance.
I am going to use this to make a toddler bed sheet and a partial top sheet by just doing the elastic on the two botom corners and finishing the top- like a top sheet
Very cool!!
26.
Susie | August 17, 2009 at 2:14 PM
Thanks for the instructions! I made a pack-n-play sheet using your Crafster tutorial.
27.
Laura | September 3, 2009 at 9:04 AM
Great easy to follow instructions…plan on making my daughter quite a few for her nursery…this is her first pregnancy…thank you for posting this information.
Laura from Texas.
28.
regina woodson | September 9, 2009 at 9:39 PM
I can’t wait to make my son some Star Wars sheets, do you know the measurements for the top sheet and pillowcase? I haven’t sewn in a LONG time and this will be my first attempt and I would appreciate any hints or tips you have! Thank you!
29.
Donna Dodd | September 13, 2009 at 1:52 PM
Ok. I’ve made 2 crib sheets (1 fleece, 1 flannel) perfectly with this tutorial. I started again yesterday to make a 3rd (fleece) and I totally screwed it up. I measured just as before and the sheet was about 3 – 4 inches too long and 3 – 4 inches too wide. I have fixed the corners but now I have extra material that I’m scared to cut in case I screw it up more. It wouldn’t be that big a deal but the material cost me $24 and it’s going to be a gift for a baby shower! Please help me or tell me to “just cut it!”
(15 minutes later) So I’ve been playing with the extra material on the corners & I’ve folded it to where I don’t have to cut, just sew it up. I pray that it works but I’m so scared to take the sheet off the bed. I’ll probably forget what I’m supposed to do. I’ll let you know how it turns out.
(2 hours & lunch later) I’ve got 2 corners complete & 1 left to do! Since the whole thing was messed up, I left 1 corner intact and worked on the other 3. Taking a break and will finish it later!
30.
Kymy | September 13, 2009 at 5:43 PM
I am sorry you had such a hard time this time! When using knits or any stretchy fabric such as a lot of fleece it can really scew the sizing, because different knits have a different stretch & recovery. I am sorry that you had such problem especially when it worked find in the past. If you run into this again in the future or someone using stretchy fabric does… if you get the corners fixed so they fit don’t be afraid to cut some off! You want it to go over the bottom side of the mattress by at least 3-4″ more won’t hurt. You just want to stretch you elastic out as much as possible when sewing it on to bring it in tight, or you can put elastic all the way around stretching as tight as you can as you sew. I hope the rest goes smoothly & the recipient enjoys it!
31.
QT Pie Bows | October 15, 2009 at 12:37 PM
I hust made my daughters toddler bed sheets and matching pillowcase! AWESOME! Thank you so much for this tutorial!!
32.
Annie | October 15, 2009 at 1:40 PM
Hi- Have you tried doing two fitted bottom corners and a top sheet top? Should I follow the same measurements?
33.
Kymy | October 15, 2009 at 2:06 PM
I have! I make it 8″ shorter the long way when cutting it (the length not width). Then I only cut the corners on one end, and I use a 2″ hem for the ‘top’ edge instead of repeating the corners if that makes sense! I have only made one, I am making some for the girls soon, so I will take pics
34.
Angie | October 26, 2009 at 2:07 PM
Thank you so much for the tutorial. Its’ great!
35.
Karen | October 26, 2009 at 5:04 PM
I have my first grandchild on the way and a family wooden crib. The crib mattress in 33 in by 15 in by 2 in. Can you please help me out with how to change the measurements? Thanks so.
36.
Kymy | October 26, 2009 at 6:14 PM
Cut a piece of fabric 37″ X 19″ instead & use 4 inch corners. Then use smaller pieces of elastic (7″?) instead, you may have to play around with it a hair.
37.
karen | November 6, 2009 at 10:33 AM
trying to make these sheets. The fabric I bought was only 44 inches wide. After pre-washing, only 43 inches. Do I still cut 8 inch template? Or should I make it smaller?
38.
Kymy | November 6, 2009 at 10:53 AM
You should be fine using the 8″ template. I never actually measure the width, I just buy fabric that says 44″/45″ on the bolt because it varies so much.
39.
Laura | November 20, 2009 at 12:25 AM
I’ll be a grandmother next Tuesday and I wanted to make something special and practical for my new grandson. I’m off to the fabric store today!
Thank you so much for such easy instructions!
40.
Kendra | December 31, 2009 at 12:21 PM
Awesome instructions!! Like a few others that posted on here..would love to know the measurements/proper amount of fabric to buy for twin mattress.
41.
Jill | January 1, 2010 at 4:16 PM
Thank you for the fantastic tute. It was so easy to follow!
42.
eileen | January 3, 2010 at 2:39 PM
Thankyou just what i need have been asked to make some cot sheets for twins due soon.have got yards and yards of sheeting from millshop and only cost £5 so thankyou so much.
43.
Karen/Oklahoma | January 9, 2010 at 7:13 PM
What a big favor you have done for many. As I read your tutorial, I was thinking how nice you must be to do this for us. Can’t wait to try these sheets!
Thanks again and blessing to you!
44.
KDB | January 16, 2010 at 12:36 PM
Great pictures and directions! Very easy to follow and understand. Thank you so much for posting this!
45.
Jeewanthi | January 17, 2010 at 12:29 AM
I’ll be a mom next March and before two weeks I visited your site and learned how to make a crib sheet. I did 3 sets so far and it is very neat. Thanks to you “It is just FANTASTIC” no words to explain.
Since the pictures are there no one will miss it. Thanks a million. God Bless you….
46.
Barb | January 19, 2010 at 9:49 AM
Just wanted to say thanks for such a great tutorial. Made my first (of many, I’m sure) this weekend.
Posted a link to the tutorial on my blog. Hope that was okay!
47.
Kymy | January 19, 2010 at 12:31 PM
I’m glad that you liked it so much!!! And that’s perfectly fine! I encourage people to share links, just not use my actual pictures without permission.
48.
Diana | January 29, 2010 at 7:41 AM
I have some really cute knit that I’d like to make a sheet out of. Do you have a pattern for knits or any tips on how to adjust this one?
49.
Kymy | January 29, 2010 at 11:43 AM
If it’s nice & stretchy I would make it 2″ shorter & 2″ skinnier and use 7.5″ squares instead of 8″! Hope that helps!
50.
erin, maker of chimes | February 15, 2010 at 6:58 PM
This is just what I was needing–thank you! Just found out that we’ve got a boy on the way, so it’ll be John Deere fabric for me too
51.
Sharon | February 22, 2010 at 7:18 PM
Wow, thanks for the tips. Been looking for a DIY like this.
52.
San | March 9, 2010 at 4:11 PM
Hi, I wonder if I could put a link to this tut on my fav tut’s section of my blog? Do I need to formalize a request? Thanks for posting this!
53.
Kymy | March 9, 2010 at 5:54 PM
no need to ask to share links
You can use the picture/button if you want to link to my blog tutes list or if you just want to do the tutorial you may use 1 picture of the finished product, just make sure it is linked back. I just ask people don’t copy any of the stuff off my blog. Linking is A-OK!
54.
Lynnet | March 13, 2010 at 7:06 PM
Great directions and pictures! I needed a refresher since it’s been 11 years since I last made some and I’m making cradle and crib sheets for a friend. Great job!
55.
Emily | March 22, 2010 at 6:22 AM
Love the tutorial. We recently bought a camper that has bunks for the kids that are enclosed 1/2 way. It is a pain to make the beds. I thought about adding elastic to the top sheet and comforter to hold them in a bit better after I make the bed. Do you have any suggestions for that?
56.
Jackie | April 1, 2010 at 8:19 AM
I came across your tutorial and think you make it sound so easy! I am currently trying to make the sheets for the first time for a friends baby shower, and wanted to know if I am supposed to finish all four sides, or just the two cut ends. Please (anyone) let me know ASAP.
57.
Kymy | April 1, 2010 at 9:26 AM
you can do it either way! The sides you don’t cut won’t show as they are under the mattress & they won’t fray so they can be left alone. I normally don’t finish them because I’m not going to see them anyways! But if you want a more polished look you can finish them as well!
58.
Lenetta @ Nettacow | April 19, 2010 at 11:41 AM
I found your awesome tutorial via a search for crib sheets – had I know how stinkin’ easy it was, I’d NEVER have bought any! I’ll be making a Care Bear sheet for the toddler bed in the hopes of luring my 3 year old out of the crib… wish me luck! :>)
59.
Emily | April 19, 2010 at 11:47 AM
I was wondering where you get your fabric? Do you find it inexpensively? I live in a very rural area and I will have to drive at least an hour to a chain fabric store so I was wondering if you know of any great online places for cotton to make sheets.
60.
Kymy | April 19, 2010 at 12:04 PM
I also live in a rural area & have to drive 45 minutes to the closest Wal-mart that has a small selection or take a $15-$20 30 minute ferry ride (only if no lines) & another 15-20 minute drive to get to JoAnns… so I know where you are coming from! Honestly the best thing to do is to stock up once a month when you go to town. You can also find cheap fabric at the thrift store as well.
I do have local quilt shop I buy from, it isn’t cheap, but the quality isn’t either! You can also find some stuff on line, but if you looking for stuff for less then $5 a yard it’s generally not worth it after shipping. Good luck!
61.
rebekah | May 5, 2010 at 6:13 PM
hello! if the crib mattress is 27 1/2″ x 52″ but only 3 1/2″ think, should i modify the measurements?
62.
Kymy | May 5, 2010 at 7:03 PM
That is a few inches thinner then most which are normally closer to 5. You could either make it 2″ smaller in each direction or just stretch the elastic longer so that it pulls tighter underneath making it fit on top.
63.
Michelle | May 8, 2010 at 6:59 AM
Thank you so much! I’ve been wanting to start sewing. I have two boys – almost 3 yrs and 11 months. In eigth grade, close to 20 yrs ago, I had an introduction to sewing but never made anything. This was my first project! I used my moms machine that is well over 30 yrs old – worked perfectly. It took me a long time to make! But, I’m going to make a fitted top sheet next! Your instructions with the pictures were wonderful!!! Thank you! I look forward to exploring your site more.
64.
whitney tollison | May 16, 2010 at 4:49 AM
I love that you post this and was wondering how I could change it a little! I got three daughters which love the feel of sateen fabric! The older ones I can buy sheets and what not for them! I have made simple things like pillows and curtains for them! My question is I have sateen fabric to make a fitted sheet and other bedding but don’t know if I need to wash it first, maybe cut a little different!? Any advise on what to do?
65.
Kymy | May 16, 2010 at 10:26 AM
You should really have to do anything different! You will just want to use a warm iron (make sure it’s not to hot!) to press your hem & pins to hold it in place before sewing the hem so the fabric doesn’t slide around, otherwise everything is done the same! I ALWAYS pre-wash my fabric before sewing it, no matter what kind it is! Good luck.
66.
whitney tollison | May 16, 2010 at 8:08 PM
That was great. Thank you so much! I was a little worried that I might mess up, but thanks to you keeping it simple and pictures was great! Really like the one with little man to cute!
67.
Lisa | May 17, 2010 at 7:24 PM
I really want to try and make these but the measurements of the cot matress are 1300mm X 690mm X 125mm. How should I adjust the pattern?
68.
Kymy | May 17, 2010 at 9:35 PM
That is almost the exact same sized standard crib mattress that the tutorial is made for!!! Yours is a little thinner so if you want you can make it 1 inch shorter in each direction but use the same size square cuts for the corners. If you don’t like working in inches there are free measurement converters online. Good luck!
69.
Kandy | May 18, 2010 at 9:58 AM
I made a fitted crib sheet out of some stretchy knit material my mom had 25 years ago for my son from a magazine-style book I had bought. I lost the book, but I would love to make moreof these type of fitted crib sheets. Do you have the correct amounts of fabric needed to make one like that. I sure hope so. Here in the midwest it was nice to have a fabric that was a bit warmer on those cold winter nights. Thanks for the site and hopefully for the right dimensions.
70.
Kymy | May 18, 2010 at 4:03 PM
If knits stretch both ways make it 2″ shorter in each direction & use 7.5″ squares. If the knit only stretches in one direction cut that direction the same as the woven & the other 2″ shorter. I hope this makes sense, good luck!
71.
Kandy | May 20, 2010 at 1:39 PM
Kymy Thank you for the help. I really appreciate it.
72.
Megan | June 10, 2010 at 2:54 AM
I bought a couch and it has lighter cushions than I thought = my dogs are going to destroy them even though I added the fabric protection. So, I’m thinking about trying to cover them with something that I can remove and wash. This sheet will work fine with two of the cushions but not my last one because my last one is not perfectly square there is a section that sticks out. I can’t figure out how to do this – here are the measurements – the short ends of the rectangle are 35 and 42 inches. One long side of the rectangle is 62 inches – the tricky long side = 11 inches then it comes in 7 inches and the final side is 51 inches. I hope this makes sense – I’m not sure how to go around the part the sticks out. Any ideas?
73.
Kimberly Johnson | July 8, 2010 at 7:07 PM
I have made a few of these, and also your pack n play sheets. They are a huge money saver for me. Do you have the size of a top sheet or no? I wanted to make my friend son a set for his bed, he 4 almost 5, but do not like the ones you can find in stores. I seen them online, just can’t find out how to make them. Thanks.
74.
Kymy | July 8, 2010 at 10:26 PM
I haven’t got it finished yet, but I actually have a great tutorial in the works for the semi-fitted top sheets I have made & posted a few times, hopefully later this month I will get it posted, I don’t have the measurements off hand though.
75.
Brandi | July 30, 2010 at 5:55 AM
I love this tutorial…. it is great! I have used it several times to make sheets for friends and family.
76.
Denise in Georgia | August 23, 2010 at 10:00 AM
New nonnie again!! in September 2010. Your tutorial makes this seem so easy. Can’t wait to try it. Thanks a bundle!!
77.
Marbree | August 25, 2010 at 11:05 AM
Do you leave the selvages attached or cut them off? You only talk about hemming/serging the raw ends.
I already cut off the selvages from my fabric, should I hem the long sides too to keep it from unraveling? (I don’t own a serger.) Will that make my sheet too narrow?
Thanks.
78.
Kymy | August 25, 2010 at 11:22 AM
Yes I just leave the selvages, it gives me a little extra fabric to wrap around the mattress, if you gut them off then you need to finish the edges because they are now raw edges. I don’t think they will be too narrow, just a bit more narrow, I would try using a narrow hem if possible.